Order: 階
filter circuits:濾波電路
frequency response:幅頻響應
Passband :通頻帶、傳輸帶寬
repeatedly cycle:重復周期
maximum signal to noise ratio:最大信噪比
gain constants:增益系數,放大常數
circuit topologies:電路拓撲結構
gain shortfall:增益不足
maximum output:最大輸出功率
last stage:末級
preceding stage:前級
stage filter:分級過濾器
Gain Stage:增益級
voltage amplitude:電壓振幅
Component values: 元件值
maximum valued: 最大值
minimum valued: 最小值
standard value:標準值
resistors: 電阻器
capacitors:電容器
operational amplifiers:運算放大器(OA)
circuit board:(實驗用)電路板
active filters:有源濾波器
supply currents:源電流
power supplies:電源
bypassing capacitors:旁路電容
optimal:最佳的;最理想的
Gain Bandwidth:帶寬增益
passive component:無源元件
active component: 有源元件
overall spread:全局;總範圍
Component characteristics:組件特性
Modification:修改;更改
data book:數據手冊
typical values:標準值;典型值
default values:省略補充
program execution:程序執行
Reset button:復原按鈕
positive temperature coefficient:正溫度系數
variable resistors:可變電阻器
cermet resistor:金屬陶瓷電阻器
output resistance:輸出電阻
distortion:失真
single amplifier:單級放大器
voltage follower:電壓輸出跟隨器
troubleshooting:發現並修理故障
control panel,:控制面板
1、打開crack的軟件後,根據濾波器的設計要求,在filter type中選擇濾波器的類型(Gaussian:高斯濾波器、Bessel:貝塞爾濾波器、butterworth:巴特沃斯;Chebyshev1切比雪夫1;Chebyshev2切比雪夫2;Hourglass:對三角濾波器、Elliptic:橢圓濾波器、Custom:自定義濾波器、Raised Cos:升余弦濾波器、Matche:匹配濾波器 、Delay:延遲濾波器);
2、在filter class中選擇濾波器的種類(低通、高通、帶通、帶阻);
3、在filter Attributes中設置濾波器的階數(Order)、通頻帶頻率(Passband frequency);
4、在Implementation中選擇有源濾波器(active )、無源濾波器(passive)和數字濾波器(Digital);
5、在Freq Scale中選擇Hertz和Log,如果選擇了Rad/Sec(壹種單位),則要註意Rad/Sec=6.28*Hertz;
6、在Graph Limits中設置好圖像的最大頻率和最小頻率,最大頻率要大於通頻帶的截止頻率;在Passive Design/Ideal Filter Response中觀察傳輸函數(Transfer Function)、時域響應(Time Response)、零極點圖(Pole Zero Plots)、頻域響應(Frequency Response)的圖像;
7、在Circuit Parmaters中設置源電阻(Source Res)和負載電阻(Load Res);最後點擊Circuits觀察濾波器電路圖;
8、在設計有緣濾波器的時候還要註意在Active Implementation 中選擇濾波器的電路布局形式壹般有源濾波器選擇Pos SAB型的,在Circuit Parmaters中設置增益大小(gain)。